| 61.25.1120.001.21.1504 Standard 5 Slewing Ring Bearings | L:749.3 mm; J max.:635 mm; R2:46.038 mm; PG:1/4 NPT; R1:122.237 mm; S:4.763 mm; A2:285.75 mm; P60°:364 kN; RG:1 NPT; H:422.275 mm; Stabilizing ring:SR-40-34; Cap bolt recommended tightening torque:271.2 N·m; ba:98.425 mm; Initial grease fill:2154.6 g; Da:359.999 mm; P150°:120 kN; Eye bolt:2 x 3/8-16 UNC; N1:34.925 mm; Pa:77 kN; J min.:571.5 mm; |
| 282.30.1175.013 Type 110/1300.2 Standard 5 Slewing Ring Bearings | R2:27.781 mm; H1:101.6 mm; A2:149.225 mm; H:192.484 mm; Pa:8.1 kN; L:349.25 mm; Initial grease fill:286.33 g; Da:160 mm; R1:60.325 mm; H2:41.275 mm; J1:53.975 mm; PG:1/8 NPT; Appropriate attachment bolt size G:0.625 in; A1:98.425 mm; P120°:38.3 kN; Stabilizing ring:2 x SR-1518; End plug (suffix Y):EPR 11; N1:19.05 mm; h:38.1 mm; Mass pillow block:21.3 kg; |
| 61.30.1500.200.11.1504 Standard 5 Slewing Ring Bearings | s1:19.8 mm; d1 ≈:33.74 mm; Mass complete bearing:0.19 kg; Hexagonal key size for grub screw N:3.175 mm; d:25.4 mm; B4:5 mm; Recommended tightening torque for grub screw:4 N·m; Thread grub screw G2:1/4-28 UNF; B:34.1 mm; D:52 mm; Basic dynamic load rating C:11.9 kN; Calculation factor f0:14; C:15 mm; Limiting speed1):4300 r/min; Fatigue load limit Pu:0.335 kN; r1,2 min.:0.6 mm; Basic static load rating C0:7.8 kN; |
| 61.25.1355.575.11.1403 Standard 5 Slewing Ring Bearings | B:49 mm; l2 max.:319 mm; l1 min.:125 mm; Mass rod end:7.9 kg; r1 min.:1 mm; dk:92 mm; Material constant KM:330; l7 min.:85 mm; d:70 mm; Specific dynamic load factor K:100 N/mm²; G:M 56x4; α:6 °; d2 max.:162 mm; Basic static load rating C0:490 kN; C1 max.:43 mm; h:235 mm; Basic dynamic load rating C:315 kN; |
| 161.25.0980.890.11.1503 Standard 5 Slewing Ring Bearings | da min.:371 mm; r1,2 min.:5 mm; Da min.:507 mm; s1 max.:27.9 mm; Ca min.:3.9 mm; Misalignment factor k1:0.117; B1:229 mm; B2 ≈:238 mm; G:Tr 380x5; da max.:464 mm; Basic static load rating C0:8000 kN; Fatigue load limit Pu:585 kN; d2 ≈:423 mm; Operating clearance factor k2:0.094; B:192 mm; Basic dynamic load rating C:5000 kN; D:600 mm; d1:340 mm; Da max.:580 mm; G1:35 mm; |
| 12.35.1960.400.11.1503 Standard 5 Slewing Ring Bearings | Specific dynamic load factor K:100 N/mm²; Sealing solution:Triple-lip seals; M:3 mm; Lubricant:Regular relubricatio; Design (sliding contact surface combination):Steel/steel; r2 min.:1 mm; ra max.:0.6 mm; Da min.:66.2 mm; da max.:50.1 mm; d:45 mm; Basic dynamic load rating C:156 kN; C:28 mm; Basic static load rating C0:780 kN; B:43 mm; b1:4.6 mm; Material constant KM:330; Da max.:70.5 mm; Specific static load factor K0:500 N/mm²; |
| 12.30.1381.001.41.1503 Standard 5 Slewing Ring Bearings | Mass pillow block:342 kg; N1:41.275 mm; RG:1 NPT; Eye bolt:2 x 1/2-13 UNC; A2:368.3 mm; Cap bolt, SAE grade:8; L:831.85 mm; A1:222.25 mm; Appropriate attachment bolt size G:1.5 in; Max. speed for Taconite seal:325 r/min; Taconite seal:TER 553; P180°:285 kN; P120°:260 kN; End plug (suffix Y):X-5217-2; R1:130.175 mm; PG:1/4 NPT; P60°:691 kN; J min.:628.65 mm; H2:95.25 mm; da:239.713 mm; |
| 232.20.1000.503 Type 21/1200.2 Standard 5 Slewing Ring Bearings | P60°:449 kN; P180°:185 kN; L:869.95 mm; A2:315.119 mm; Labyrinth ring (dc shaft position):LOR 164; Cap bolt:4 x 1 1/2-6 UNC; R1:163.512 mm; PG:1/4 NPT; PosiTrac Plus contact element (dc shaft position):B10724-161; Stabilizing ring:SR-0-40; R2:50.8 mm; Appropriate attachment bolt size G:1.5 in; Pa:120 kN; P90°:271 kN; H2:101.6 mm; J1:139.7 mm; Da:419.999 mm; J min.:666.75 mm; PosiTrac Plus contact element (db shaft position):B10724-175; |
| 92.25.1502.990.11.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:1160 N; Accessories:Two Seals; Shielded or Sealed B1:7.1 mm; d:6.400 mm; Oil Speed Rating Open/Shielded n2:48000 rpm; Basic Dynamic Radial Load Rating C:2810 N; Grease Speed Rating Open/Shielded n1:39000 rpm; Fillet Radius ra:0.41 mm; D:19.1000 mm; Width Plain B:5.6 mm; Sealed Speed Rating n3:27000 rpm; |
| 191.20.1400.990.41.1502 Standard 5 Slewing Ring Bearings | B:32 mm; Da max.:158.5 mm; Db min.:159 mm; T:34.5 mm; D:170 mm; Fatigue load limit Pu:31.5 kN; Ca min.:5 mm; Calculation factor e:0.43; Calculation factor Y:1.4; Da min.:149 mm; ra max.:3 mm; rb max.:2.5 mm; d:95 mm; Calculation factor Y0:0.8; C:27 mm; Reference speed:3200 r/min; Cb min.:7.5 mm; r1,2 min.:3 mm; d1 ≈:126.98 mm; Basic static load rating C0:275 kN; |
| 61.30.1320.001.21.1504 Standard 5 Slewing Ring Bearings | Mass bearing:0.0076 kg; B:6 mm; Da max.:17 mm; D:19 mm; da max.:8.4 mm; Basic dynamic load rating C:1.53 kN; da min.:8 mm; Calculation factor kr:0.03; d:6 mm; d2 ≈:8.5 mm; Calculation factor f0:7.9; Fatigue load limit Pu:0.025 kN; Limiting speed:43000 r/min; Basic static load rating C0:0.585 kN; ra max.:0.3 mm; r1,2 min.:0.3 mm; Reference speed:85000 r/min; D2 ≈:16.5 mm; |
| 280.30.1475.013 Type 110/1600. Standard 5 Slewing Ring Bearings | RG:1/8 NPT; Cap bolt, SAE grade:5; ba:27.781 mm; H2:25.4 mm; Cap bolt:2 x 1/2-13 UNC; J max.:241.3 mm; Stabilizing ring:2 x SR-13-0; R2:15.875 mm; H1:76.2 mm; J min.:206.375 mm; R1:44.45 mm; H:147.637 mm; L:279.4 mm; P120°:17.8 kN; P90°:30.2 kN; Labyrinth ring (dc shaft position):LOR 37; da:65 mm; Ca:39.014 mm; Pa:12 kN; db:77.787 mm; |