| 92.30.1799.991.21.1502 Standard 5 Slewing Ring Bearings | H:24 mm; Pu:4.770 kN; d:35 mm; D1:37 mm; Grease:2 800 min-1; static Cor:105.000 kN; D:68 mm; rs (min):1 mm; Oil:3 800 min-1; d1:68 mm; dynamic Cr:58.830 kN; |
| 162.25.1077.890.11.1503 Standard 5 Slewing Ring Bearings | Grease Speed Rating n1:1200 rpm; Fillet Radius rb:1.50 mm; D:400.0000 mm; d:260.000 mm; Fillet Radius ra:3.00 mm; Oil Speed Rating n2:1400 rpm; Basic Static Radial Load Rating Co:1320000 N; B:130.00 mm; Basic Dynamic Radial Load Rating C:702000 N; |
| 281.30.1000.013 Type 110/1200.1 Standard 5 Slewing Ring Bearings | D:190 mm; r1s (min):2.5 mm; Dynamic (Ca):393 kN; B:50 mm; d2:105 mm; rs (min):3 mm; C:43 mm; r2s (min):1 mm; T:53 mm; Static (Coa):570 kN; a:44 mm; Pu:61.550 kN; |
| 62.25.0886.106.11.1504 Standard 5 Slewing Ring Bearings | D:80.0000 mm; Grease Speed Rating n1:5600 rpm; Oil Speed Rating n2:7500 rpm; Accessories:No Shield, no Seal,; d:40.000 mm; Sealed Speed Rating n3:5600 rpm; B:30.20 mm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:49000 N; Basic Dynamic Radial Load Rating C:49500 N; |
| 282.30.1375.013 Type 110/1500.2 Standard 5 Slewing Ring Bearings | Specific dynamic load factor K:150 N/mm²; α:5 °; d4 ≈:105 mm; d2 max.:182 mm; Basic static load rating C0:655 kN; B:55 mm; l7 min.:88 mm; d:80 mm; G:M 80x4; Material constant KM:330; h1:295 mm; l3 min.:85 mm; l5 ≈:45 mm; Mass rod end:19 kg; Basic dynamic load rating C:600 kN; r1 min.:1 mm; C1 max.:48 mm; l4 max.:389 mm; dk:105 mm; w:90 mm; |
| 91.30.1415.990.11.1502 Standard 5 Slewing Ring Bearings | L:161.925 mm; Da:114.3 mm; N1:12.7 mm; a:7.144 mm; A1:79.375 mm; Limiting speed:4100 r/min; A6:14.287 mm; S:0.794 mm; B:73.025 mm; A:63.5 mm; Attachment bolt diameter G:11.113 mm; Basic dynamic load rating C:84.5 kN; d2:73.819 mm; A3:22.225 mm; J:136.525 mm; A4:15.875 mm; A2:40.481 mm; da:49.212 mm; A5:15.875 mm; s:25.4 mm; |
| 12.30.1381.000.11.1503 Standard 5 Slewing Ring Bearings | Grease Speed Rating n1:2800 rpm; d:80.000 mm; Accessories:No Shield, no Seal; Sealed Speed Rating n3:2800 rpm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:106000 N; B:44.40 mm; Basic Static Radial Load Rating Co:95000 N; Oil Speed Rating n2:3800 rpm; D:140.0000 mm; |
| 62.25.1180.001.21.1504 Standard 5 Slewing Ring Bearings | D1 ≈:723 mm; Limiting speed:170 r/min; Mass bearing:469 kg; Da max.:758 mm; Calculation factor e:0.3; b:22.3 mm; Fatigue load limit Pu:780 kN; D:790 mm; B:248 mm; d:480 mm; Calculation factor Y2:3.4; Basic static load rating C0:12000 kN; r1,2 min.:7.5 mm; ra max.:6 mm; Basic dynamic load rating C:7367 kN; Calculation factor Y1:2.3; K:12 mm; d2 ≈:560 mm; Calculation factor Y0:2.2; |
| 60.20.0944.575.01.1403 Standard 5 Slewing Ring Bearings | B:13.00 mm; d:95.000 mm; Oil Speed Rating Open/Shielded n2:6000 rpm; Fillet Radius ra:1.00 mm; D:120.0000 mm; Basic Dynamic Radial Load Rating C:19900 N; Sealed Speed Rating n3:3000 rpm; Basic Static Radial Load Rating Co:21200 N; Grease Speed Rating Open/Shielded n1:5000 rpm; Accessories:One Shield; |
| 282.30.1400.013 Type 110/1600.2 Standard 5 Slewing Ring Bearings | Specific dynamic load factor K:120 N/mm²; Specific static load factor K0:250 N/mm²; Permissible sliding velocity v min.:0 m/s; Mass strip:0.14 kg; H:1 mm; Coefficient of friction µ min.:0.02; Coefficient of friction µ max.:0.2; B:100 mm; Permissible sliding velocity v max.:2.5 m/s; L:500 mm; |
| 62.20.1094.500.01.1503 Standard 5 Slewing Ring Bearings | P0°:5400 kN; Cap bolt, rec. tightening torque:400 N·m; Da:540 mm; ATS:380 mm; Ca:212 mm; Q180°:1430 kN; Cap bolt, size:M 30x220; Q120°:2860 kN; db:320 mm; H:631 mm; H2:115 mm; s:23 mm; N:50 mm; ba min.:154 mm; P120°:2500 kN; N1:42 mm; A1:330 mm; P180°:2800 kN; J6:820 mm; P55°:7000 kN; |
| 231.21.1075.013 Type 21/1200.1 Standard 5 Slewing Ring Bearings | B1:2 mm; Tolerance shaft:h8; Specific static load factor K0:20 N/mm²; Mass bushing:0.003 kg; D:10 mm; d:5 mm; D1:12 mm; Specific dynamic load factor K:10 N/mm²; Coefficient of friction µ max.:0.1; Coefficient of friction µ min.:0.05; B:6 mm; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Permissible sliding velocity v min.:0.25 m/s; |